Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with an MVT license plate.
Made in Switzerland. Designed for the highest loads and proven in racing.
Mounting:
- Starter pinion: Clean the MVT pole wheel, then screw the counterpart for the cable starter onto the pole wheel (secure the enclosed screws with Loctite).
- Pull starter: Position the starter housing in the correct position and tap lightly with a plastic hammer until the pull starter fits perfectly. It can then be screwed into place.
Application:
- Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
- Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Further helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber hammer etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Surface | chrome-plated, raw |
| Ignition system | MVT Allumage |
| Ø outside | 130 mm |
| Total length | 170 mm |
| Color | Chrome, black-matt |
| Number of fixing points | 2 pcs |
| Width | 150 mm |
| Height | 82 mm |
| Hole spacing | 138 mm |
| Puch | E50 |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Type of application: 1K · Area of application: Chemistry · Contents [ml]: 10 ml · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Temperature resistance (min.): -75 - 200 °C · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 26.70
EUR 2’670.00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Chain pitch: 1/2" x 3/16" · Manufacturer: GPO · Material: Steel · Surface: chrome-plated · Number of teeth: 28 pcs · Color: Chrome · Ø outside: 15.9 mm · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Total length: 257 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
EUR 73.10
MVT internal rotor ignition incl. rev limiter & light 12V | Puch / Sachs
Manufacturer: MVT Allumage · Manufacturer: swiing · Ø cable: 7 mm · Tension: 12 V · Performance: 65 W · Direction of rotation: left · Ø mounting plate: 96 mm · Ø Flywheel outside: 49.2 mm · Number of fixing points: 2 pcs · Mounting type: Screws · Weight: 268 g · Area of application: Tuning
EUR 445.60
swiing® ingenious special screw M6x12 drive pinion pull rope starter MVT
Material: Steel · Surface: galvanized (blue) · Drive: Hexagon socket · Total length: 12 mm · Manufacturer: swiing® ingenious parts · Screw head: Countersunk head · Thread type: M6x1 (standard thread) · Width across flats SW: 4 mm
EUR 3.55
Moped fans also bought
GPO gasket set | Puch E50
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Area of application: Standard · Number of components: 7 pcs · Ø outlet inside: 19.9 mm · Hole spacing outlet: 42 mm · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Hole spacing inlet: 32 - 38 mm
EUR 12.10
swiing® revival screw set engine galvanized | Puch Maxi
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Drive: Cross recess · Drive: Hexagon socket · Screw head: Countersunk head · Screw head: Cylinder head · Screw head: Lens head · Puch OEM number: 900.1216 · Puch OEM number: 901.1308
EUR 12.10
MVT internal rotor ignition incl. rev limiter & light 12V | Puch / Sachs
Manufacturer: MVT Allumage · Manufacturer: swiing · Ø cable: 7 mm · Tension: 12 V · Performance: 65 W · Direction of rotation: left · Ø mounting plate: 96 mm · Ø Flywheel outside: 49.2 mm · Number of fixing points: 2 pcs · Mounting type: Screws · Weight: 268 g · Area of application: Tuning
EUR 445.60
Collection only possible with online purchase and appointment.
