Hot 
Differences from the original BADASS Diablo cylinder:
- On the GPO cylinder, the web of the split exhaust port is slightly ground down to minimize the risk of an exhaust-side heat seizure.
- On the GPO tuning cylinder, the edges of the overflow channels near the cylinder neck have been chamfered to facilitate piston ring installation.
- The original BADASS cylinder is shipped with a GOL piston, while the GPO Divertimento is equipped with a GPO piston matched to the cylinder. Differences are evident, among other things, in the crown profile and in the cutouts on the piston skirt for the overflow channels.
- On the GPO Divertimento, more space has been created for the nuts used to secure the cylinder base.
- The required M6x62 mm stud bolts for mounting the cylinder base, as well as nuts, washers, and stud bolts for the intake, are included as standard with the GPO.
- The intake tract has been repositioned so that the carburetor and air filter are now aligned horizontally and no longer point diagonally upward.
- On the BADASS Diablo, the embossed “30 km” logo is positioned off-center, whereas on the GPO Divertimento it is centered, as on the original Swiss cylinder.
The cylinder base is factory-designed for Swiss 50/2 (502) engines. However, the mounting holes for the German 50/2 engine casing are marked. This allows you to drill them out if necessary and use the cylinder as usual for your moped with a German engine casing.
The large intake allows for the use of the 17 mm swiing® tuning carburetor, provided it is mounted with a short air filter cap, a matching clamp (short), and the appropriate cover plate (long/deep). Please note the installation direction during assembly. The piston is installed with the arrow pointing toward the exhaust on the exhaust side. You can find the larger 43 mm version of the racing kit, the matching 17 mm carburetor, and the air filter parts described above in the accessories section. A good, affordable standard replacement part. GPO – GOOD PARTS ONLY.
Manufacturer: GPO · Material: Gray cast iron · Displacement: 55 ccm · Nominal diameter: 41 mm
Manufacturer: GPO · Nominal diameter: 41 mm · Material: Aluminum · Ø outside piston (A): 40.95 mm · Ø piston pin (B): 12 mm · Compression height (C): 28 mm · Curvature (D): 3.4 mm · Total piston height (E): 50.5 mm · Number of piston rings (F): 2 pcs · Piston ring mold: Rectangular ring · Piston ring impact: Internal fuse (IS) · Piston ring height: 1.5 mm · Thick piston ring: 1.7 mm
Manufacturer: GPO · Material: Sealing carton · Number of components: 4 pcs
Manufacturer: GPO · Material: Steel · Surface: blackened · Diameter: 5.3 mm · Thread type: M6x1 (standard thread) · Total length: 62 mm · Thread length: 11.8 mm, 7.8 mm · Width across flats: 10 mm · Strength class: 10.9 · Drive: External hexagon · Nominal diameter (thread): 6 mm
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: M5x0.8 (standard thread) · Total length: 26 mm · Thread length: 14 mm, 7 mm · Width across flats: 8 mm · Strength class: 8, 10.9 · Drive: External hexagon · Nominal diameter (thread): 5 mm
| Sachs | 50 (Fahrtwind, 1.25 / 1.5 hp, DE) 502 (Saxonette) - AL , AML 50/2 - L CH (0.8 PS) , ML CH (0.8 PS) , MB (2.6 PS) , MLB (2.6 PS) 50/3 50/4 - MLFB (2.6 PS) , LKH (4.5 PS) |
Accessories & related products
swiing® revival screw set cylinder head Inox | Sachs 503 / 50/2 / 50/3 / 50/4
Manufacturer: swiing® revival parts · Thread type: M6x1 (standard thread) · Number of components: 12 pcs · Material: Chrome steel (colloquially known as stainless steel) · Nominal diameter (thread): 6 mm · Drive: External hexagon · Thread length: 22 mm · Total length: 34 mm · Screw head: Hexagon · Ø shaft: 5.85 mm · Shank: Yes · Width across flats: 10 mm · Shank length: 8 mm · Area of application: Standard
EUR 9.10
Cigar Exhaust System (Ø 32 / 70 mm) Chrome | Sachs 50/2
Manufacturer: Made in Portugal · Material: Steel · Surface: chrome-plated · Ø outside: 70 mm · Total length: 700 mm · Color: Chrome · Ø Internal connection: 32 mm · Ø Flame tube outside: 32 mm · Exhaust type: Cigar · Mounting type: Screwed clamp · Flame tube attachment: Union nut
EUR 128.60
swiing® revival carburetor 17 mm Bing SSB 1/17/69
Nominal diameter: 17 mm · Manufacturer: swiing® revival parts · Camouflaged: No · Component group Carburetor: Carburetor complete · Material: Aluminum · Carburetor type: SSB · Nozzle size: 76 · Total length: 132 mm · Height: 100 mm · Hole spacing inlet: 31 mm · Width: 85 mm · Mounting type: Flange · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Area of application: Standard · Area of application: Tuning · Choke control: without choke
EUR 155.50
swiing® ingenious gasket cylinder head 41 mm | Sachs 503, 502, 50/2, 50/3, 50/4
Nominal diameter: 41 mm · Manufacturer: swiing® ingenious parts · Place of use: Cylinder head · Material: Aluminum · Ø cylinder: 41 mm · Ø inside: 41.7 mm · Thickness: 0.3 mm · Hole pattern [mm]: 37 x 37 · Area of application: Standard
EUR 6.00
swiing® ingenious exhaust nut M40x1.5 long 32 mm manifold | Sachs
Ø inside: 32.5 mm · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: chrome-plated · Thread type: MF40x1.5 (fine pitch thread) · Nut type: Union nut · Height: 22 mm · Nominal diameter (thread): 40 mm · Ø outside: 45 mm
EUR 26.60
swiing® ingenious hook wrench M40 exhaust nut | Sachs 50/2
Manufacturer: swiing® ingenious parts · Surface: galvanized (blue) · Number of components: 1 pcs · Material: Rubber · Material: Steel · Total length: 280 mm · Width: 67 mm · Height: 5 mm · Ø inside: 33 mm · Ø outside: 46 mm · Weight: 300 g · Area of application: Workshop accessories
EUR 30.50
BAD ASS cylinder head L Ø 41-43 mm | Sachs 502, 50/2, 50/3, 50/4
Manufacturer: BAD ASS · Material: Aluminum · Ø cylinder: 41 - 43 mm · Hole pattern [mm]: 37 x 37 · Ø outside: 108 mm · Number of fixing points: 1 pcs · Number of fixing points: 4 pcs · Area of application: Tuning · Ø screw holder: 19.3 mm · Decompressor: M10x1.5
EUR 183.70
Explore categories from Cylinder
Moped fans also bought
Hot
swiing® revival nozzle set M3.5 (64 - 74) Bing SRE, SRA, SRC, SRF
Manufacturer: swiing® revival parts · Component group Carburetor: Spraying · Material: Brass · Quantity: 6 pcs · Carburetor type: SRA (1/11/31) Velux · Carburetor type: SRA (1/11/35) Velux · Carburetor type: SRC · Carburetor type: SRE · Carburetor type: SRF · Nozzle type: Main nozzle · Drive: Slot · Nozzle size: 64 · Nozzle size: 66 · Nozzle size: 68 · Nozzle size: 70 · Nozzle size: 72 · Nozzle size: 74 · Total length: 6 mm · Nozzle thread: M3.5x0.6 (standard thread)
EUR 19.50
Hot
VEC electronic ignition coil (replaces ignition coil, capacitor & contact breaker)
Manufacturer: VEC · Ø cable holder: 5 mm · Place of use: Internal (in the ignition) · Color: black · Ø mounting hole: 4.6 mm · Total length: 77 mm · Ø Internal flywheel: 90 mm · Height: 48 mm · Cable length: 140 mm · Cable length: 420 mm · Mounting type: Screws · Number of fixing points: 2 pcs · Area of application: Original · Area of application: Performance · Area of application: Standard · Hole spacing: 54 mm
EUR 183.70
Not in stock
swiing® revival stud bolt set M5x26 inlet (10.9 strength) | Sachs 50/2, 502, 50/3
Manufacturer: swiing® revival parts · Thread type: M5x0.8 (standard thread) · Surface: galvanized (blue) · Material: Steel · Nominal diameter (thread): 5 mm · Drive: External hexagon · Thread length: 7 mm · Thread length: 14 mm · Total length: 26 mm · Width across flats: 8 mm · Strength class: 8 · Strength class: 10.9
EUR 7.00
GPO 41 mm piston "Divertimento" | Sachs 502, 50/2, 50/3, 50/4
Manufacturer: GPO · Material: Aluminum · Ø outside piston (A): 40.95 mm · Compression height (C): 28 mm · Curvature (D): 3.4 mm · Total piston height (E): 50.5 mm · Number of piston rings (F): 2 pcs · Nominal diameter: 41 mm · Piston ring mold: Rectangular ring · Piston ring impact: Internal fuse (IS) · Piston ring height: 1.5 mm · Thick piston ring: 1.7 mm · Ø piston pin (B): 12 mm
EUR 55.00
GPO stud bolt set "Divertimento" & "Diablo" cylinder | Sachs 502, 50/2, 50/3, 50/4
Manufacturer: GPO · Thread type: M6x1 (standard thread) · Surface: blackened · Diameter: 5.3 mm · Material: Steel · Nominal diameter (thread): 6 mm · Drive: External hexagon · Thread length: 7.8 mm · Thread length: 11.8 mm · Total length: 62 mm · Width across flats: 10 mm · Strength class: 10.9
EUR 14.60
Working late? Evening hours on Thursday until 20:00
