41 mm cast iron racing cylinder with Latin American temperament and 57 cc for your Puch M50, MS50, VS50, DS50, VZ50 small motorcycle.
The timing cam of the tuning cylinder was deliberately kept low, which results in particularly good torque in the lower engine speed range.
Thanks to the large sealing surface, no more pouring is required to close the slot on the housing compared to many other cylinder kits.
Compared to the Sombrero racing kit for Puch Velux X30 models, this version has a thinner cylinder neck so that it fits into the corresponding EX50 engine cases.
| Manufacturer | GPO |
| Material | Gray cast iron |
| Camouflaged | No |
| Area of application | Tuning |
| Displacement | 57 ccm |
| Crankshaft stroke | 43 mm |
| Ø piston pin (B) | 10 mm, 12 mm |
| Nominal diameter | 41 mm |
| Ø cylinder neck | 43 mm |
| Ø outlet inside | 25 mm |
| Ø Inlet inside | 19 mm |
| Thread inlet | M6x1 (standard thread) |
| Hole spacing outlet | 42 mm |
| Hole spacing inlet | 42 mm |
| Number of fixing points | 4 pcs |
| Outlet type | straight |
| Thread outlet | M6x1 (standard thread) |
| Hole pattern [mm] | 44 x 44 |
| Decompressor | No |
| Puch | 2-speed MS, MV, MV50 3-speed VSD, DS, VZ, MC |
Accessories & related products
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Manufacturer: Elring · Contents [ml]: 70 ml · Color: red · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Temperature resistance (min.): -60 - 300 °C · Gap dimension (max.): 2 mm · Area of application: Chemistry
EUR 28.00
EUR 400.00/l
GPO cylinder gasket set BAD ASS Lucifer / GPO Sombrero 41 mm | Puch X30 Velux, M50, MS
Manufacturer: GPO · Thickness: 0.4 mm · Thickness: 0.45 mm · Material: Aluminum · Material: Sealing paper · Area of application: Tuning · Ø cylinder: 41 mm · Ø outlet inside: 27 mm · Hole spacing inlet: 32 mm · Decompressor: Yes · Hole spacing outlet: 32 mm · Number of components: 4 pcs · Hole pattern [mm]: 44 x 44 mm
EUR 24.30
GPO Ø 41 mm "Sombrero" cylinder kit | Puch X30 Velux, NG-2AH
Nominal diameter: 41 mm · Manufacturer: GPO · Material: Gray cast iron · Area of application: Tuning · Crankshaft stroke: 43 mm · Displacement: 57 ccm · Ø cylinder neck: 44.7 mm · Ø outlet inside: 25 mm · Ø Inlet inside: 19 mm · Number of fixing points: 4 pcs · Ø piston pin (B): 10 mm · Ø piston pin (B): 12 mm · Thread inlet: M6x1 (standard thread) · Hole spacing inlet: 32 mm · Decompressor: No · Hole spacing outlet: 42 mm · Outlet type: straight · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44 · Camouflaged: No
EUR 219.70
EUR 244.10
Moped fans also bought
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Manufacturer: swiing® ingenious parts · Surface: chrome-plated · Color: Chrome · Color: black-matt · Ignition system: BOSCH · Ignition system: DUCATI · Material: Plastic · Material: Steel · Hole spacing: 137.5 mm · Total length: 160 mm · Width: 150 mm · Height: 88 mm · Ø outside: 130 mm · Number of fixing points: 2 pcs
EUR 183.00
GPO piston 41 mm (12 mm KoBo) | Puch X30 Velux, M50, MS50, VS50, DS50, VZ50
Manufacturer: GPO · Nominal diameter: 41 mm · Ø outside piston (A): 40.94 mm · Ø piston pin (B): 12 mm · Compression height (C): 23.2 mm · Curvature (D): 3.7 mm · Total piston height (E): 49.3 mm · Number of piston rings (F): 2 pcs · Piston ring mold: L-ring · Piston ring mold: Rectangular ring · Piston ring impact: Flank safety device (FS) · Piston ring impact: Internal fuse (IS) · Piston weight: 85 g
EUR 60.90
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 11.95 mm · Ø outside: 29.02 mm · Ø inside: 12 mm · Total length: 165 mm · Thread length: 40.5 mm · Thread length: 50 mm · Shank length: 74.5 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Width across flats SW: 19 mm · Ball bearing closed: Yes
EUR 47.50
Not in stock
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Diameter: 29 mm · Ø shaft: 19 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Width across flats SW: 19 mm · Ball bearing closed: Yes
EUR 43.70
EUR 47.50
swiing® revival special nut M6 SW8 (sprocket ref. back pedal / intake manifold)
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut · Drive: External hexagon · Thread type: M6x1 (standard thread) · Height: 6 mm · Width across flats SW: 8 mm
EUR 3.55
Hot 
swiing® ingenious 17 mm SRF carburetor tuning camouflaged | Puch Maxi, Supermaxi, X30 NS / NL
Nominal diameter: 17 mm · Manufacturer: swiing® ingenious parts · Camouflaged: Yes · Component group Carburetor: Carburetor complete · Material: Aluminum · Mounting type: Plug connection clamped · Carburetor type: SRE · Total length: 65 mm · Width: 47 mm · Height: 89 mm · Height: 109 mm · Ø Inside entrance: 17 mm · Ø Internal connection: 23 mm · Ø Output inside: 17.1 mm · Ø Air filter connection: 27.5 mm · Ø fuel hose connection: 5 mm · Mixed oil connection: No · Area of application: Tuning · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.2 · Nozzle size: 74 · Clamping screw torque (max.): 3 N/m · Clamping screw torque (max.): 4 N/m
EUR 146.40
swiing® revival stud bolt cylinder base M6x26 - 10.9 strength | Sachs
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 5.8 mm · Total length: 26 mm · Thread length: 9 mm · Thread length: 13 mm · Thread type: M6x1 (standard thread) · Strength class: 10.9
EUR 2.20
Hot
swiing® ingenious intake manifold 17 mm SRF camouflaged | Puch E50
Manufacturer: swiing® ingenious parts · Camouflaged: Yes · Material: Aluminum · Mounting type: Stud bolts & nuts · Ø External connection: 23 mm · Ø inside: 17 mm · Hole spacing inlet: 38 mm · Total height: 53.5 mm · Number of fixing points: 2 pcs · Height flange center hole: 42 mm · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Total length: 38 mm
EUR 54.80
swiing® ingenious intake manifold 17 mm SRF | Puch Z50
Manufacturer: swiing® ingenious parts · Material: Aluminum · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Ø inside: 17 mm · Number of fixing points: 2 pcs · Ø External connection: 23 mm · Hole spacing inlet: 38 mm · Mounting type: Stud bolts & nuts · Total height: 73 mm · Height flange center hole: 61 mm · Total length: 45 mm · Camouflaged: Yes
EUR 60.90
Collection only possible with online purchase and appointment.
