Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
| Material | Aluminum |
| Surface | blank |
| Ø inside | 30 mm |
| Ø axle | 12 mm |
| Ø Receptacle | 93 mm |
| Ø drum | 80 mm |
| Area of application | Standard, Custom |
| Number of spoke holes | 36 pcs |
| Puch |
Ratings
Accessories & related products
Hot 
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø nipple: 3.5 mm · Ø nipple: 6 mm · Nipple length: 10 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Number of components: 1 pcs · Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Cable length: 2200 mm · Area of application: Standard
EUR 2.95
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm
EUR 37.80
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Ø outside: 91 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Wide cam holder: 12 mm · Total length: 187 mm · Brake lever length (lever length): 55 mm · Cranking (offset): 8 mm
EUR 85.60
swiing® revival rear brake anchor plate | Puch Maxi N
Material: Steel · Manufacturer: swiing® revival parts · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø bore: 12.2 mm · Ø axle: 12 mm · Ø outside: 92 mm · Total length: 135 mm · Wide cam holder: 12 mm · Cranking (offset): 10 mm · Brake lever length (lever length): 68 mm · Ø screw holder: 6.5 mm
EUR 91.70
Magura set screw M6x34 mm lock nut SW10
Slotted: No · Width across flats Screw: 8 mm · Manufacturer: Magura · Width across flats nut: 10 mm · Material: Brass · Surface: nickel-plated · Ø cable holder: 3.05 mm · Ø Receptacle: 7.05 mm · Total length: 34 mm · Thread type: M6x1 (standard thread) · Thread length: 23 mm
EUR 3.05
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Shank length: 99 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 28 mm · Thread length: 52 mm · Total length: 185 mm · Width across flats: 7 mm
EUR 12.10
SKF 16101 2RS1 ball bearing 12/30/8
Bearing type: Deep groove ball bearing · Stock number: 16101 · Ø inside: 12 mm · Ø outside: 30 mm · Width: 8 mm · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard
EUR 20.00
Moped fans also bought
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Width: 125 mm · Manufacturer: GPO · Material: Aluminum · Surface: sandblasted · Ø cylinder: 38 mm · Total length: 135 mm · Height: 55 mm · Candle thread: short · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: No · Area of application: Standard
EUR 40.30
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Nipple length: 14 mm · Manufacturer: GPO · Material: Chrome steel (colloquially known as stainless steel) · Surface: raw · Quantity: 36 pcs · Length from hook: 188 mm · Nominal diameter (thread): 3.15 mm · Ø spoke head: 5.35 mm · Ø spoke: 2.9 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 ° · Thread length: 11 mm · Color: silver
EUR 67.20
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 29.02 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Ø shaft: 11.95 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 74.5 mm · Width across flats: 19 mm · Thread length: 40.5 mm · Thread length: 50 mm
EUR 47.60
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Ø outside: 91 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Wide cam holder: 12 mm · Total length: 187 mm · Brake lever length (lever length): 55 mm · Cranking (offset): 8 mm
EUR 85.60
Collection only possible with online purchase and appointment.
